adaptec raid controller manual

Options are 16, 32, 64, 128, 256, 512, and 1024. Options are low, med, and high. Configures a controller using a XML server template file produced by the SAVECONFIG command (see arcconf saveconfig on page 33). Controller rescan runs in the background, asynchronously. Saved information includes (but is not limited to) device logs, drive logs, event logs, error logs, controller logs, and SSD SMART statistics. (For more information about SMART statistics, see. Attached drives without Adaptec meta-data, but with an OS partition, are surfaced to the host operating system as RAW Pass Through devices (similar to JBODs on legacy Adaptec controllers), where the RAID layer of the controller firmware is bypassed when the host issues commands to the device. Uninitialized drives are also compatible with any HBA or can be exchanged with drives on the motherboard's SATA interface. Note: In HBA Mode, a hot-plugged new drive is automatically configured as a Raw. You can specify one or more logical drives. This setting affects the SATA disk drives on the controller. It takes effect when the SATA drives are restarted. You can set one or more timers, in any order, in a single command. Logical drive number.Esxcimomport Hypervisor CiMOM port number. The uninitialize command clears Adaptec meta-data and any OS partitions from a drive; existing data on the drive is destroyed. Drives can uninitialized only if they are in the Raw or Ready state (that is, not part of any logical drive). A drive in the Raw state has no Adaptec meta-data but may or may not have an OS partition. Uninitializes all physical devices in the Raw or Ready state.Examples ARCCONF UNINIT 1 0 12 0 13 ARCCONF 1 ALL Proprietary and Confidential to PMC-Sierra, Inc. Adaptec and the Adaptec by PMC logo are trademarks of PMC-Sierra, Inc. It contains the following sections:Adaptec controllers support single-drive volumes that can be used for drives that are not part of a RAID array. See Chapter 21 for more information.

• adaptec raid controller manual, adaptec raid controller manual.

To see a complete list of supported operating systems see the Product SpecificationsFedoraLinux Driver SourceMicrosoftSuSE LinuxUbuntuUnixVMware. To see a complete list of supported operating systems see the Product SpecificationsFedoraLinux Driver SourceMicrosoftSuSE LinuxUbuntuUnixVMwareIdeal for bandwidth intensive storage applications; NAS, OLTP servers, web servers, and digital surveillance. Offers Zero-Maintenance Cache Protection and Intelligent Power Management. A Issue: July 15, 2013. All rights reserved. The information in this document is proprietary and confidential to PMC-Sierra, Inc. In any event, no part of this document may be reproduced or redistributed in any form without the express written consent of PMC-Sierra, Inc. Document No.: CDP-00284-01-A Rev. A, Issue:. Document No.: CDP-00284-01-A Rev. A, Issue:. Document No.: CDP-00284-01-A Rev. A, Issue:. If you need further assistance, use the support options listed below. Document No.: CDP-00284-01-A Rev. A, Issue:. The Installation DVD mounts automatically. If it doesn't, mount it manually. With interactive mode, enter commands at the prompt. In batch mode, create scripts and run the script in the appropriate shell, as described in the table below. See arcconf task for more information about Secure Erase. Syntax ARCCONF ATAPASSWORD SET. Syntax ARCCONF COPYBACK. Optional parameters for specifying a stripe size. STRIPE is specified in kilobytes 16, 32, 64, 128, 256, 512 and 1024 are supported. The default is 256KB. Noprompt No prompt for confirmation Examples ARCCONF CREATE 1 LOGICALDRIVE STRIPESIZE 64 MAX 0 1 0 2 0 3 2 NOPROMPT. Examples ARCCONF DRIVERUPDATE C:\WINDOWSALL arcconf expanderlist Description Returns a list of disk drive expanders on a controller. Turns the controller failover mode on. Turns the controller failover mode off. Examples. Default is the current mode.Tabular Creates output in tabular format.Device number of the device to be updated.

This is relevant for logical arrays. Default is disabled.Displaying the disk drives adds a few seconds to the overall POST time. Default is disabled.Default is enabled. Disable this feature if you want to attach more than 48 SATA II disk drives. Available only with SATA II disk drives.The default setting is Auto, which allows the SAS card to adjust the data transfer rate as required.Default setting is Yes (enabled). Set to No (disabled) only if the controller is connected to a device that does not support CRC Checking. Default is 0. Formatting destroys all data on a disk drive.Only physical drives that appear during POST are shown.The event log is cleared of any non-persistent events each time you restart your computer. Also, when the log is full, new events overwrite old events. This platform will only perform optimally once JavaScript is activated.This is already pre-installed in the Rescue System. For this the state of your disks has to be Ready. If your disks are still in the Raw (Pass Through) state, you need to initialize the disks: Controllers found: 1If it has not, the drive is manually added to the RAID as a hot spare. The rebuild starts automatically: After replacing the defective drive, data automatically migrates back. It is also possible to remove a hot spare designation via arcconf and to mark the new replacement drive as a new hot spare. More information on this can be found on the Adaptec website at Adaptec KB5117. There is however, no guarantee that a recovery is possible. Data loss can not be excluded. More information is available at: Ask Adaptec Hetzner Online GmbH. All Rights Reserved. Configuring Raid 1 with SAS 6IR Controller. The Adaptec RAID Configuration utility provides three tools: The Array Configuration Utility (ACU) The Adaptec RAID Controller Utility (ARCU) screen appears. Land Rover, Range Rover. Note: The following section provides information on the Adaptec SATA RAID.

This can be done using the Rescan Drives option or by simply navigating back to the ARCU main menu.This is described in Parts I and II of this document.See Using the ACU to Create and Manage Arrays.Use it for modifying the controller and disk drive settings, and for checking the battery status. See Using the Select Utility to Modify Controller Settings.See Using the Disk Utilities to Manage Disk Drives.The section contains the following subsections:This is normal behavior. Instructions for completing tasks are displayed onscreen. This section contains the following subsections:However, creating an array using the GUI is up to three times as fast. For more information, see the Sun StorageTek RAID Manager Software User’s Guide.See To Initialize Disk Drives With the ACU for more information.)Check the BIOS settings to verify the correct boot order.See To Make an Array Bootable With the ACU.For more information, refer to your computer documentation.Initializing a disk drive that is part of an array might make the array unusable. Back up all data from your disk drive before you initialize it.Secure erase performs three distinct writing passes to the disk drive being erased--it does not just write zeros.You might want to perform a secure erase only on disk drives that contain confidential or classified information. Both options take less time than the secure erase option, but might not offer enough security for highly sensitive information. See Using the Disk Utilities to Manage Disk Drives ) to format a disk drive. The selected disk drive(s) cannot be used until the erase is complete.This utility is called either SerialSelect (SAS) or SATASelect. When disabled, write cache is not used on the disk drive. It is recommended that you disable write cache on the disk drive.Disabling the BIOS allows another controller to act as a bootable device.When disabled, the array must be rebuilt manually.Note that there might be a significant performance reduction. Default is disabled.

Installation OptionsPage 47: Installing the Controller and Disk Drives Installing the Controller and Disk. DrivesBefore You BeginPage 49 Chapter 5: Installing the Controller and Disk Drives ? 48Page 50 Chapter 5: Installing the Controller and Disk Drives ? 49Page 51 Chapter 5: Installing the Controller and Disk Drives ? 50. Connecting Disk Drives to Your ControllersPage 53 Chapter 5: Installing the Controller and Disk Drives ? 52. Connecting Solid State Drives (SSDs). To connect a Solid. Page 54 Chapter 5: Installing the Controller and Disk Drives ? 53Page 55: Creating a Bootable Array Creating a Bootable ArraySetting the Boot ControllerPage 57 Chapter 6: Creating a Bootable Array ? 56Creating an Array with Adaptec Storage Manager. This section describes how. Page 59 Chapter 6: Creating a Bootable Array ? 58Page 60: Installing the Driver and an Operating System Installing the Driver and an. Operating SystemPage 61 Chapter 7: Installing the Driver and an Operating System ? 60. Before You BeginPage 62 Chapter 7: Installing the Driver and an Operating System ? 61. Installing with WindowsPage 63 Chapter 7: Installing the Driver and an Operating System ? 62. Installing with Red Hat Linux 5Page 65 Chapter 7: Installing the Driver and an Operating System ? 64Page 66 Chapter 7: Installing the Driver and an Operating System ? 65Page 67 Chapter 7: Installing the Driver and an Operating System ? 66Page 68 Chapter 7: Installing the Driver and an Operating System ? 67. Installing with SolarisPage 69 Chapter 7: Installing the Driver and an Operating System ? 68Page 70 Chapter 7: Installing the Driver and an Operating System ? 69Page 71 Chapter 7: Installing the Driver and an Operating System ? 70Page 72 Chapter 7: Installing the Driver and an Operating System ? 71. Installing with FreeBSDPage 73: Installing the Driver on an Existing Operating System Installing the Driver on an Existing.

This chapter describes how to use the ARCU to create a RAID array. Runtime Software RAID Reconstructor Tutorial. Adaptec SAS RAID Con.Reload to refresh your session. Reload to refresh your session. PMC-Sierra. PMC-SierraConfidentialCopyright. All rights reserved. The information in this document is proprietary and. Page 3 ? 3. Adaptec by PMC Product Support. If you have questions about installing or using your Adaptec by PMC. Page 4 ? 4. Limited 3-Year Hardware WarrantyRegulatory Compliance Statements. Federal Communications Commission Radio Frequency Interference Statement. WARNING: Changes or modifications to this unit. Page 6 ? 6Page 8 Contents ? 8Page 10 Contents ? 10. A Introduction to SASPage 12 Contents ? 12. F Safety InformationG Technical SpecificationsPage 14 Chapter 1: About This Guide ? 13. What You Need to Know Before You BeginPage 15: Kit Contents and System Requirements Kit Contents and System. RequirementsPage 16 Chapter 2: Kit Contents and System Requirements ? 15. Kit ContentsPage 18: About Your RAID Controller About Your RAID ControllerPage 19 Chapter 3: About Your RAID Controller ? 18. Standard RAID Controller Features. Page 20 Chapter 3: About Your RAID Controller ? 19Page 21 Chapter 3: About Your RAID Controller ? 20. About the Adaptec RAID 5085About the Adaptec RAID 5405About the Adaptec RAID 5445About the Adaptec RAID 51245About the Adaptec RAID 51645About the Adaptec RAID 52445About the Adaptec RAID 5405ZAbout the Adaptec RAID 5445ZAbout the Adaptec RAID 2045About the Adaptec RAID 2805About the Adaptec RAID 6405About the Adaptec RAID 6445About the Adaptec RAID 6405EAbout the Adaptec RAID 6805EAbout the Adaptec RAID 6405TChoosing a RAID LevelPage 43 Chapter 4: Getting Started ? 42. Selecting Disk Drives and CablesPage 44 Chapter 4: Getting Started ? 43Page 45 Chapter 4: Getting Started ? 44. To replace the full-height bracket with the low-profile bracket:Page 46 Chapter 4: Getting Started ? 45.

132Page 134 Appendix E: Controller LED and I2C Connector Quick Reference ? 133Page 135 Appendix E: Controller LED and I2C Connector Quick Reference ? 134Page 137 Appendix E: Controller LED and I2C Connector Quick Reference ? 136Page 138 Appendix E: Controller LED and I2C Connector Quick Reference ? 137. Adaptec RAID 2045 LED Connector SpecificationPage 141 Appendix E: Controller LED and I2C Connector Quick Reference ? 140Page 142 Appendix E: Controller LED and I2C Connector Quick Reference ? 141. Specification. Page 143 Appendix E: Controller LED and I2C Connector Quick Reference ? 142Page 145 Appendix E: Controller LED and I2C Connector Quick Reference ? 144Page 146 Appendix E: Controller LED and I2C Connector Quick Reference ? 145Page 147 Appendix E: Controller LED and I2C Connector Quick Reference ? 146Page 148: Safety Information Safety InformationPage 149: Technical Specifications Technical SpecificationsEnvironmental SpecificationsA managing with ACU 106ACU RAID 10. Page 152 Index ? 151Page 153 Index ? 152H enclosure. Page 154 Index ? 153Runtime BIOS setting 111 Adaptec RAID Configuration utility 81Sunnyvale, CA 94089 USA. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. All rights reserved. In any event, no part of this document may be reproduced or redistributed in any form without the express written consent of PMCSierra, Inc. Other product and company names mentioned herein may be trademarks of their respective owners.PMC-Sierra, Inc. expressly disclaims all representations and warranties of any kind regarding the contents or use of the information, including, but not limited to, express and implied warranties of accuracy, completeness, merchantability, fitness for a particular use, or non-infringement. In no event will PMC-Sierra, Inc.If you need further assistance, use the support options listed below.

To expedite your service, have your computer in front of you. The TSID number identifies your product and support status. Please visit the Support section of www.adaptec.com for the most up to date contact information. For support via e-mail, submit your question at ask-de.adaptec.com. For support via e-mail, submit your question at ask-fr.adaptec.com. For support via e-mail, submit your question at ask.adaptec.com. If the product should become defective within the warranty period, PMC-Sierra, at its option, will repair or replace the product, or refund the purchaser’s purchase price for the product, provided it is delivered at the purchaser’s expense to an authorized PMC-Sierra service facility or to PMC-Sierra. All replaced parts or products shall become the property of PMC-Sierra. This warranty shall not apply if the product has been damaged by accident, misuse, abuse or as a result of unauthorized service or parts. The purchaser shall bear all shipping, packing, and insurance costs and all other costs, excluding labor and parts, necessary to effectuate repair, replacement or refund under this warranty. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

Operating SystemBefore You BeginPage 75 Chapter 8: Installing the Driver on an Existing Operating System ? 74. Installing on WindowsPage 76 Chapter 8: Installing the Driver on an Existing Operating System ? 75. Installing on Debian LinuxInstalling on SolarisPage 78 Chapter 8: Installing the Driver on an Existing Operating System ? 77Page 79 Chapter 8: Installing the Driver on an Existing Operating System ? 78. Installing on FreeBSDPage 80: Managing Your Storage Space Managing Your Storage SpacePage 81 Chapter 9: Managing Your Storage Space ? 80. About Adaptec Storage ManagerPage 82 Chapter 9: Managing Your Storage Space ? 81. About the Adaptec RAID Configuration UtilityPage 83 Chapter 9: Managing Your Storage Space ? 82Page 84: Solving Problems Solving ProblemsPage 85 Chapter 10: Solving Problems ? 84. Troubleshooting ChecklistPage 86 Chapter 10: Solving Problems ? 85. Recovering from a Disk Drive FailurePage 87 Chapter 10: Solving Problems ? 86Page 88 Chapter 10: Solving Problems ? 87Page 89: Introduction to SAS Introduction to SASTerminology Used in This ChapterPage 91 Appendix A: Introduction to SAS ? 90. How Do SAS Devices Communicate?Page 92 Appendix A: Introduction to SAS ? 91. What’s a SAS Port?Page 93 Appendix A: Introduction to SAS ? 92. How are Disk Drives Identified in SAS?Some backplanes support daisy-chain expansion to other backplanes. For example, you can. Page 95 Appendix A: Introduction to SAS ? 94. How is SAS Different from Parallel SCSI?Page 96: Understanding RAID Understanding RAIDUnderstanding Drive SegmentsPage 98 Appendix B: Understanding RAID ? 97. RAID 1 ArraysPage 99 Appendix B: Understanding RAID ? 98. RAID 10 ArraysPage 100 Appendix B: Understanding RAID ? 99. RAID 5 ArraysPage 101 Appendix B: Understanding RAID ? 100. RAID 5EE ArraysPage 102 Appendix B: Understanding RAID ? 101. RAID 50 ArraysPage 103 Appendix B: Understanding RAID ? 102. RAID 6 ArraysPage 104 Appendix B: Understanding RAID ? 103.

Selecting the Best RAID LevelPage 105: Using the Adaptec RAID Configuration Utility Using the Adaptec RAID. Configuration UtilityIntroduction to the ARC UtilityPage 107 Appendix C: Using the Adaptec RAID Configuration Utility ? 106. Managing Existing Arrays. To view or modify existing arrays. Page 108 Appendix C: Using the Adaptec RAID Configuration Utility ? 107. Option Description. Power Off Drive After The duration of. Page 109 Appendix C: Using the Adaptec RAID Configuration Utility ? 108. Initializing Disk Drives. If a disk drive appears grayed-out. Page 110 Appendix C: Using the Adaptec RAID Configuration Utility ? 109Page 111 Appendix C: Using the Adaptec RAID Configuration Utility ? 110Page 112 Appendix C: Using the Adaptec RAID Configuration Utility ? 111. General Controller Settings. Note: Default settings are shown in. Page 113 Appendix C: Using the Adaptec RAID Configuration Utility ? 112. Backplane Mode ? Series 2, Series 5. Page 114 Appendix C: Using the Adaptec RAID Configuration Utility ? 113Page 115 Appendix C: Using the Adaptec RAID Configuration Utility ? 114. Identifying Disk DrivesPage 116: Using the Adaptec Flash Utility Using the Adaptec Flash UtilitySystem RequirementsPage 119 Appendix D: Using the Adaptec Flash Utility ? 118Page 120 Appendix D: Using the Adaptec Flash Utility ? 119. These switches are available. Verify. Compares the contents of each of the flash components. Page 122 Appendix D: Using the Adaptec Flash Utility ? 121. Updating the Flash Using the AFU Command LineQuick ReferenceAdaptec RAID 5085 LED Connector Specification. Page 125 Appendix E: Controller LED and I2C Connector Quick Reference ? 124Specification. Page 127 Appendix E: Controller LED and I2C Connector Quick Reference ? 126Page 129 Appendix E: Controller LED and I2C Connector Quick Reference ? 128Page 131 Appendix E: Controller LED and I2C Connector Quick Reference ? 130Page 133 Appendix E: Controller LED and I2C Connector Quick Reference ?

However, if this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Adaptec by PMC products are for use only with UL listed ITE. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. This equipment is designed for home use but it may causes radio frequency interference problem if used too near to a television or radio. Please handle it correctly per this documentation. Dispose of used batteries according to the.For more information, see About Your RAID Controller on page 17. This guide uses these terms: Your RAID controller creates arrays, which your operating system (and Adaptec Storage Manager) recognizes as logical drives. For more information, refer to the Adaptec Storage Manager User’s Guide on the Adaptec Installation DVD. If your kit does, the type and quantity vary—for cable information about your controller, visit the Adaptec Web site at www.adaptec.com.) For more information, see page 81. For more information, refer to the Adaptec Storage Manager User’s Guide or online Help. Striped Mirrors are also supported on Series 2 and Series 6E controllers. To purchase a flash backup module, refer to the Adaptec Web site at www.adaptec.com. You can also use Adaptec Storage Manager or the ARCCONF command-line utility to upgrade your controller firmware. Refer to the Adaptec Storage Manager User’s Guide and the Adaptec Command Line Interface User’s Guide. It describes the options you have for installing your Adaptec RAID controller and disk drives and creating arrays for storage.

It also describes how to prepare your controller for installation into a low-profile computer cabinet. Improved performance but no redundancy (see page 96 ). Redundancy, but reduced capacity (see page 97 ). Redundancy and improved performance (see page 98 ). When selecting disk drives for your RAID array, ensure that all the disk drives have the same performance level. You can use different-sized disk drives in the array, but the array will be limited to the capacity of the smallest and slowest disk drive. For more information about arrays, refer to the Adaptec Storage Manager User’s Guide or online Help.For more information or to purchase cables, visit the Adaptec Web site at www.adaptec.com. The full-height bracket is mounted on the front of the controller, the low-profile bracket is mounted on the back of the controller, as shown in the figure below. The full-height bracket is installed on the front side of the controller, with the mounting screws inserted from the back of the controller, as shown in the Figure 1. Using a Phillips head screw driver, remove the mounting screws, as shown in Figure 2, then set the screws aside for use in Step 2. The low-profile bracket is installed on the back side of the controller, with the mounting screws inserted from the front of the controller, as shown the Figure 3. Be sure to install the bracket with Be sure that the controller is not bent after attaching the low-profile Follow the steps for the installation option you’ve chosen. Unique storage innovations featured on certain RAID adapters include maxCache caching software, Zero-Maintenance Cache Protection (ZCMP) and maxCrypto controller-based encryption (CBE.) All adapters feature maxView storage manager, which provides an HTML5 web interface that can be used in standard desktops and mobile browsers for all storage configuration and management needs. SmartRAID adapters also feature backwards compatibility, broad operating system support and CPU platform diversity.

They have been added to our trusted Smart Storage platform to support deployments that use fewer drives and can benefit from cachingThe SmartRAID 3100 series also unlocks all the features and performance of the 12 Gbps HBA 1100 Series of host bus adapters when the drives are configured as raw devices. The SmartRAID family continues its battery-free portfolio. The SmartRAID 315x series integrates flash-based cache protection to enable instant cache protection. The tethered Adaptec ASCM-35F capacitor module supports a five-year lifetime and is continuouslySmartRAID 3162 adapters also feature integrated cache backup circuitry, NAND Flash memory and field-replaceable super capacitors.Find out how the SmartROC 3100 and SmartIOC 2100 handle these advanced security features using maxCrypto controlled-based encryption (CBE). Solving Problems Troubleshooting Checklist Monitoring Disk Drives Status Silencing the Alarm Recovering from a Disk Drive Failure Failed Disk Drive Protected by a Hot Spare Failed Disk Drive Not Protected by a Hot Spare Failure in Multiple Arrays Simultaneously Disk Drive Failure in a RAID 0 Array Multiple Failures in the Same Array Failed Drive in maxCache Pool Resetting the Controller Introduction to SAS Terminology Used in This Chapter What is SAS. How Do SAS Devices Communicate. What’s a Phy? What’s a SAS Port? What’s a SAS Address. What’s a SAS Connector. What do SAS Cables Look Like. How are Disk Drives Identified in SAS. What are the SAS Connection Options. Direct-attach Connections Backplane Connections SAS Expander Connections How is SAS Different from Parallel SCSI.The information in this document is proprietary and confidential to PMC-Sierra, Inc., and for its cu stomers’ internal us e. In a ny event, no part of this document may be repr oduced or redistributed in any form without the express written consen t of PMC- Sier ra, Inc. T rademar ks PMC, PMC-Sierra, and A daptec are r egistered trademarks of PMC-Sierra, Inc.

“ Adaptec b y PMC” is a trademark of PMC-Sierra, Inc. Other pr oduct and c ompany na mes mentio ned herein ma y be trademarks of their re spectiv e owners.PMC-Sierra, Inc. expr essly disclaims all repr esentations and warranties of a ny kind regarding the c ontents or use of the information, incl uding, but not limited to, expr ess and implied warranties of accurac y, complet eness, merc hantability, fit ness for a particular use, or no n-infringement. In no ev ent will PMC-Sierra, Inc.Patents The technology discussed in this document may be pr otected by one or mor e patent grants. If you need further assistance, use the support options listed belo w. T o expedite y our serv ice, ha ve y o ur computer in fr ont of you. T ec hnical Support Identification (TSID) Number. Before c ontacting T echnical S upport, you need y our pr oduct un ique TSID n umber. The TSID number id entifies your pr oduct and support status. ? The TSID number is included on a white, bar -c oded label, like this example. It ’ s rec ommended that y ou register your pr oduct so that you ha v e easy access t o your TSID when c ontacting product support. Note: The phone numbers below are subject to change. Please visit th e Suppor t section of www.adaptec.com for the most up to date contact information. Japan ? Visit our W eb site at www.adaptec.c o.jp. ? Call 03-3367-3970 (fax).If the pr oduct should bec ome defectiv e within the warranty p eriod, PMC-Sierra, at its option, will repair or repl ace the product, or r efund the purchaser’ s purchase price for th e product, pr ovided it is deliver ed at the purchaser’ s expense to an authorized PMC-Sierra serv ice facility or to PMC-Sierra. 2. Repair or re placement parts or products will be furnished on an exchange basis and will either be new or recondition ed and w i ll be subject to original warr anty term. All replaced parts or products shall become the pr operty of PMC-Sierr a.

This warrant y shall not apply if the product has been damaged b y accident, mi suse, abuse or as a result of unauthorized serv ice or parts. 3. W arranty ser vice is available t o the purch aser by deliv ering the pr oduct during the warranty per iod to an au thorized PMC-Sierra serv ice facility or to PMC-S ierra and providing proof of pu rchase price and date. The purc haser shall bear all shipping, packing, and insurance costs and all other co sts, ex clud ing labor and parts, necessar y to effectuate repair, replacem ent or refund under this warranty. 4. For mor e information on ho w to obtain warranty service, wr ite or t elephone. Americas PMC-Sierra, Inc. Japan PMC-S ierra, at T okumasu-Building 4F, 5-5-5, Higashinakano, N akano-ku, T o kyo 164-0003, J apan, 03-3367-3970 (fax). 5. THIS LIMITED W ARRANTY D OES NO T EXTEND T O ANY PRODUCT WHICH HAS BEEN D AMAGED AS A RESUL T OF A CCIDENT, MISUSE, ABUSE, OR AS A RESU L T OF UN A UTHORIZED SER VICE OR P AR TS. 6. THIS W ARRANTY IS IN LIEU OF ALL O THER EX PRESS W ARRANTIES WHICH NOW OR HEREAFTER MIGHT OTHER WISE ARISE RESPECT TO THIS PR ODUCT.This equipment has been tested and found to comply with the limits for a Class B digita l device, pursuant to Part 15 of the FCC r ules. These limits are designed to provide re asonable protection against harmful interf er ence in a residential installation. This equipment generates, uses, and can radiate radio frequency ener gy, and if not installe d and used in accordance wi th the instruction manual, may cause harmf ul interference to radio communications. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may no t cause harmful interferenc e and (2) this device must accept an y interfere nce rece ived, includin g interfer ence that may cause undesired ope ration. UL Compliance Statement Adapt ec by PMC pr oducts are t ested and listed b y U nderw riters Laboratories, Inc.